Check your tyre pressure every two to four weeks, before a long journey and before carrying a heavier load than usual. Follow any more frequent checks specified in your vehicle handbook, and measure the pressure when the tyres are cold for a reliable reading.
Why regular pressure checks matter
Tyres naturally lose small amounts of air over time, even without an obvious puncture. A tyre can be significantly underinflated before it looks flat, so a visual inspection cannot replace a pressure gauge.
Too little pressure allows the tyre to flex more as it rolls, increasing heat and potentially damaging its internal structure. It can also make steering less precise, increase fuel consumption and wear the tread unevenly. Too much pressure can affect ride comfort, tread wear and the way the tyre contacts the road.
A routine pressure check usually takes only a few minutes once you know the recommended settings. Check all four road tyres during the same session rather than measuring only the one that looks low. If your vehicle has a spare tyre, include it according to the handbook because it can lose pressure while unused.
When to check more frequently
Check the pressures before a long journey, even if your usual checking date has not arrived. Sustained driving places greater demands on tyres, and correcting low pressure beforehand reduces avoidable stress on them.
Also check before carrying extra passengers, substantial luggage or a trailer. Some vehicles specify higher pressures for a full load, sometimes with different settings for the front and rear wheels. Use the manufacturer's loaded settings rather than adding an estimated amount of air.
Take an additional reading after a hard impact with a pothole or kerb, particularly if you notice vibration, steering changes or a tyre that looks softer. Pressure loss after an impact can indicate tyre, valve or wheel damage. Visible sidewall damage or a bulge needs professional inspection, even if the pressure appears normal.
If one tyre repeatedly needs topping up, shorten the interval between checks while arranging an inspection. Adding air replaces what has escaped but does not fix the cause. A tyre that loses pressure rapidly should not be driven on; follow the vehicle's instructions for using a spare or obtaining assistance.
Where to find the correct tyre pressure
The recommended pressures are usually printed on a label in a door opening, inside the fuel filler flap or in the vehicle handbook. They apply to the vehicle's specified tyre sizes and loading conditions. Front and rear pressures may differ, so read each setting carefully.
Do not use the pressure moulded into the tyre sidewall as your everyday target. That marking generally relates to the tyre's maximum pressure or load rating, not the vehicle manufacturer's recommended operating pressure.
Pressure may be shown in bar, psi or kPa. Set your gauge or inflator to the same unit as the manufacturer's figure to avoid a conversion mistake. If the car has non-standard wheels or a tyre size not listed in the handbook, ask a qualified tyre specialist to confirm suitable settings.
A space-saving spare often requires a substantially different pressure from the road tyres. Check its specified pressure separately, along with any operating restrictions printed on it or stated in the handbook.
How to measure tyre pressure accurately
For a cold reading, check before driving or after the car has been parked for at least three hours, unless the handbook specifies otherwise. Driving heats the tyres and raises the pressure inside them. Releasing air from a warm tyre to match the cold setting can leave it underinflated once it cools.
- Find the correct cold pressure for each axle and the current load.
- Remove the valve cap and press a reliable gauge firmly and squarely onto the valve.
- Read the pressure once the gauge is properly seated. Reposition it if you hear air escaping around the connection.
- Add air if the reading is low, or release a little if a cold tyre is above the recommended setting.
- Measure again after adjustment, then refit the valve cap securely by hand.
Use a gauge you trust, and check its battery if it has a digital display. If a reading seems unlikely, repeat it or compare it with another reliable gauge. Inspect the tread and sidewalls while checking pressure, but do not remove embedded objects because this may release air quickly.
What tyre pressure warning systems can tell you
A tyre pressure monitoring system provides a useful warning, but it does not replace regular manual checks. Depending on its design, it may alert you only after a noticeable pressure drop or infer a problem from wheel rotation rather than measuring pressure directly.
If a warning appears while driving, stop somewhere safe and check for visible damage before continuing. Measure all the tyres as soon as it is safe to do so, and do not assume the tyre looks acceptable simply because it has not visibly collapsed.
After correcting the pressures, some systems need a reset or calibration through the vehicle controls. Follow the handbook and reset the system only after checking every tyre against the correct setting. If the warning returns or the same tyre keeps losing air, arrange a professional leak inspection rather than repeatedly clearing the alert.